![]() ![]() Also when flashing from a windows client I like to open a command prompt window and pass the following command (no quotes) "ping 192.168.1.1 -t -i 200" and watch the TTL responses during the process. Note 2: While not always necessary it is also a best practice to set your computer to a static IP of 192.168.1.8 (or to whatever subnet the router is on) for flashing. Note 1: If you get an error message stating that the firmware you are loading is the same or older than the stock firmware on the unit, that is fine. In web browser, go to (you should be back at the set password screen again).wait for router to reboot and Power light to go solid green again (5 minutes). From telnet pass the following command (without quotes): "nvram erase & reboot".Telnet over to router (username = root & password = the one you just set).While these last few steps may not be necessary, the wiki author has performed them without issues. Note: Some users have needed to reset NVRAM from the CLI, see the "NO 30-30-30 reset." section below for details. Set Password, Login and manually configure DD-WRT.Create a password using the standard DD-WRT GUI.In web browser, go to (you should see the DD-WRT create password screen).Reset router (as documented above), and wait for router to reboot and Power light to go solid green again.(Why wait? See peacock Note 1 "Important2" bold paragraph.) wait at least 5 minutes longer (5 full earth minutes) for it to fully reboot and power light to go solid green again. chk firmware file you downloaded from table above. Click on Advanced > Administration > Router Update.In web browser, go to or netgear default username & password is "admin" & "password" respectively (no quotes).This should be the ONLY connection for the router & PC Connect PC to one of router's LAN ports with an network cable (using router for DHCP is okay).Wait for Power light to go solid green again.After releasing Reset button, router should reboot with much flashing of lights.Note: WiKi author recommends holding reset for at least 20 seconds. The router resets, and returns to the factory configuration Reset Per Netgear Documentation: Use the end of a paper clip or a similar object to press and hold the Reset button on the back of the router for at least 7 seconds.Turn on router, wait for Power light to go solid green, then reset router:.Also see the Peacock Announcement for historical reference on Broadcom routers, even if some details do not apply to an ARM device.įrom stock Netgear firmware to DD-WRT on a R6300v2: This has boardid U12H240T99: see more info at Netgear AC1450 Flashing Instructions Also see the R6300v2 Versions section above about the "Spectrum Wifi" variant.See yellow highlights in screenshot below for details.If there is a "CH" download the "CH" initial flash file, if not you can use the regular initial flash file.Check the Stock Firmware version for a trialing "CH". ![]() Click on Advanced > Administration > Router Status.In web browser, go to or and login (if you have to reset details, including default username/password, are in flash section below).Connect to the router (using router DHCP is fine) via LAN cable or WiFi.DD-WRT Kong Mod for NETGEAR R6300v2CH () (login required)ĭetermine your R6300v2 variant & download the proper initial flash file from the table above:.Support for netgear R6300 / R6300v2?.NOTE: You can find Kong initial flash files for the R6300v2CH at the following links Netgear R6300v2 COX Linkīe careful to flash the correct INITIAL firmware for your version! Version For further information about updating these units see this thread. None of the below files seem to work in the upgrade process. Another ISP unit is for "COX Communications" with boardid U12H240T33.The Initial Flash R6300V2CH.chk file from Kong worked, along with upgrading. There is another ISP unit for "Spectrum Wifi" with a blue stripe, no "CH" on the bottom label, and whose firmware has no trailing "CH".When you open the stock firmware web interface you will note a "CH" at the end of the stock firmware name/version. Charter (an ISP) puts out a custom R6300v2 unit with "Model: R6300v2" on the bottom and blue coloring on the front, not the standard yellow. There are at least three variants of the R6300v2 device. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |